OFFICIAL EMLID RESELLER
Emlid range · Dual-camera GNSS RTK receiver
Emlid Reach RS4 Pro
Emlid's most complete multi-band GNSS RTK receiver. Its two Full HD cameras enable augmented-reality stakeout and measuring inaccessible points from photos. It delivers centimetre accuracy, even under tree canopy.
From €3,999 excl. VAT · commissioning and training by DART Solutions

672
channels, L1/L2/L5/L6 bands
7 mm
+ 1 ppm, horizontal RTK accuracy
2 cameras
Full HD with global shutter
16 h
battery life as an RTK rover
IP68
from −40 to +65 °C
Offers and prices
The receiver on its own, ready for the field, or as a base and rover pair.
RECEIVER ONLY
Reach RS4 Pro
€3,999 excl. VAT
• Two Full HD cameras
• Carrying case, USB-C cable
• LoRa 860-930 MHz and UHF 410-470 MHz antennas
READY FOR THE FIELD
Reach RS4 Pro essential kit
€4,425 excl. VAT
• Reach RS4 Pro and its bumper
• Survey pole with smartphone mount
• Quick release adapter
WORKS WITHOUT A NETWORK
Base and rover kit
€7,550 excl. VAT
• RS4 Pro as rover, RS4 as base
• Corrections over UHF or LoRa radio
• Adapters and bumpers for both
Public prices excluding VAT as published by Emlid (October 2026), shipping not included, subject to change; project and volume pricing on request.
What makes the difference
Augmented-reality stakeout
The design is overlaid on the live image: you see exactly where to put the stake, even on a complex site.
Measuring from images
Façades, points behind a fence or across a road: measure them without placing the pole there, and without a total station.
Accuracy under canopy
672 channels and multi-band tracking for a reliable centimetre fix in forests or dense urban areas.
Unlimited tilt
Compensation ready after a few movements, with no calibration and no magnetic interference: 18 mm at 30° tilt.
Dual-band radio and LTE
LoRa 868/915 MHz up to 1 W, UHF 410-470 MHz up to 2 W (TRIMTALK 450S) and an LTE modem for NTRIP networks.
Built to last
Magnesium alloy housing, IP68, operation from −40 to +65 °C and a play-free quick release mount.

AUGMENTED REALITY
Stake out while seeing the design on site
Instead of following coordinates on a map, the operator sees the design overlaid on the camera image. Crews work faster, including on complex road and construction sites.
• Dynamic navigation to the point
• Automatic target view
• Cut and fill indicator
• Quick switching between points
IMAGE-BASED MEASURING
Measure what the pole cannot reach
A few photos taken with the RS4 Pro are enough to measure an inaccessible point. No instrument set-up, and no need to enter hazardous areas.
• Building façades and corners
• Areas behind a fence
• Points above traffic
• Water, pits or running machinery


EMLID FLOW AND FLOW 360
Field and office in sync
The Emlid Flow app (iOS and Android) controls the receiver in the field and syncs instantly with the Emlid Flow 360 platform.
• Topographic surveys and CAD stakeout
• Alignments, offsets and curves
• Slopes, cut and fill
• Shared projects and real-time tracking
Reach RS4 Pro specifications
Dimensions and weight
128.6 × 128.6 × 99.3 mm · 943 g
Ruggedness
Magnesium alloy · IP68 · −40 to +65 °C
GNSS
GPS, GLONASS, Galileo, BeiDou, QZSS, NavIC · L1/L2/L5/L6 · 672 channels
RTK accuracy
H: 7 mm + 1 ppm · V: 14 mm + 1 ppm
PPK accuracy
H: 5 mm + 0.5 ppm · V: 10 mm + 1 ppm
Static accuracy
H: 4 mm + 0.5 ppm · V: 8 mm + 1 ppm
Tilt
RTK + 2 mm + 0.3 mm/° · no angle limit
Fix and update rate
Convergence ≈ 5 s · up to 10 Hz
Cameras
2 × 1/2.6" CMOS with global shutter, Full HD, 25 fps
LoRa radio
868/915 MHz · up to 1 W · range up to 8 km
UHF radio
410-470 MHz · up to 2 W · TRIMTALK 450S
LTE modem
4G/3G/2G · nano-SIM card
Connectivity
Wi-Fi 802.11a/b/g/n · Bluetooth 5.1 · RS-232 · USB-C
Battery life
Li-ion 5,000 mAh, 36 Wh · 16 h as RTK rover, 22 h logging
Charging
USB-C Power Delivery up to 15 V / 3 A · power bank supported
Data
NTRIP, RTCM3 · NMEA, LLH/XYZ · RINEX, UBX · 16 GB
Indicative values. Specifications provided by Emlid. Public prices excluding VAT as published by Emlid (October 2026), shipping not included, subject to change; project and volume pricing on request.

DART Solutions, your official Emlid reseller since November 2026
Buying from DART means support from choosing the equipment right through to the field, from a team based in France.
Advice and selection
We start from your sites and deliverables to choose the right receiver, the right correction source and the right accessories.
Commissioning
Base and rover set-up, NTRIP or radio corrections, coordinate system and ready-to-use Emlid Flow projects.
Training
Hands-on training in the field: surveying, stakeout, accuracy checks and data exchange with the office.
Support and after-sales
A single point of contact for your questions, your updates and liaison with Emlid for warranty claims.
Reach RS4 Pro FAQ
RS4 or RS4 Pro: which one should I choose?
They share the same GNSS electronics, the same radios and the same accuracy. The RS4 Pro adds the two cameras for augmented-reality stakeout and image-based measuring. It is ideal for stakeout and urban surveying. The RS4 is enough for conventional surveys and as a base.
Do I need a base to work in RTK?
Not necessarily. The RS4 Pro receives corrections from an NTRIP network (VRS or CORS) through its LTE modem or the smartphone. Without network coverage, it is paired with a Reach RS4 base over UHF or LoRa radio: that is the base and rover kit.
Which software does it work with?
With Emlid Flow on iOS or Android, synced with Emlid Flow 360 in the office. The receiver also outputs its positions in NMEA for compatible third-party apps, and its raw data in RINEX for post-processing.
What is the real battery life?
Emlid states 16 h as an RTK rover with tilt compensation and 22 h when logging. It charges over USB-C, including from a power bank or in a vehicle.
Does DART handle commissioning?
Yes. As an official Emlid reseller, we configure the receiver and corrections, prepare your projects and train your crews in the field.
A project with the Reach RS4 Pro?
Demo, quote or advice on the set-up: let's talk about your sites.
Request a quote