Opens in a new tab

OFFICIAL EMLID RESELLER

Emlid range · GNSS RTK module for drones

Emlid Reach M2

Emlid's multi-band GNSS RTK module for drones and autonomous systems. It weighs 35 g and provides centimetre positioning in RTK or PPK. Synchronised with the camera shutter, it greatly reduces the number of ground control points.

From €649 excl. VAT · module only

Module GNSS RTK Emlid Reach M2 pour drone

35 g

56 × 45 × 15 mm

L1/L2

multi-band, 184 channels

7 mm

+ 1 ppm, kinematic accuracy

100 km

PPK baseline

16 GB

of RINEX logging

Offers and prices

The module on its own to integrate your own antenna, or the complete solution with a ground base.

MODULE ONLY

Reach M2

€649 excl. VAT

• Reach M2 module

• Micro-USB cable

• 6-pin and 5-pin JST-GH cables

READY TO MOUNT

Reach M2 with GNSS antenna

€897 excl. VAT

• Reach M2 module and cables

• Multi-band helical GNSS antenna

• 0.5 m SMA adapter cable

BASE + DRONE

Reach M2 unmanned systems kit

€3,500 excl. VAT

• Reach M2 with GNSS antenna

• Reach RS3 as ground base

• Camera hot shoe adapter and extension

Public prices excluding VAT as published by Emlid (October 2026), shipping not included, subject to change; project and volume pricing on request.

Accurate georeferencing, on board

Camera synchronisation

Connected to the hot shoe, the module timestamps every shot with sub-microsecond resolution.

Fewer control points

With PPK, ground control points are only needed to check the model's accuracy.

Real-time RTK

Centimetre position sent to the autopilot (Pixhawk cables available) for autonomous systems.

RINEX logging

Raw data with photo events up to 10 Hz, on 16 GB of internal memory.

Free processing

Post-process RINEX files with Emlid Studio or RTKLIB, with no licence.

Open

Works with Reach bases as well as any RTCM3 and NTRIP compatible receiver or network.

Emlid Reach M2 avec antenne GNSS multibande et câbles

INTEGRATION

Everything to equip your drone

The M2 is powered at 5 V via USB or JST-GH and communicates over UART, USB or Wi-Fi. An optional LoRa radio receives corrections from a Reach base up to 8 km away.

• Optional multi-band GNSS antenna

• Camera hot shoe adapter

• Cables for Pixhawk autopilots

PPK in four steps

STEP 1

Connect

Connect the Reach M2 to the hot shoe of the drone's camera.

STEP 2

Fly

The module logs the position and time of every shot.

STEP 3

Download

Download the logs from the M2 and the base (Reach RS, CORS network or other).

STEP 4

Process

Emlid Studio computes the accurate geotag file for the photos.

Reach M2 specifications

Dimensions and weight

56.4 × 45.3 × 14.6 mm · 35 g

Temperature

−20 to +65 °C

Power supply

4.75 to 5.5 V via USB or JST-GH · 300 mA typ. at 5 V

Antenna

3.3 V bias · optional GNSS antenna

GNSS

GPS/QZSS L1C/A, L2C · GLONASS L1OF, L2OF · BeiDou B1I, B2I · Galileo E1B/C, E5b

Channels and update rate

184 channels · 10 Hz

Static accuracy

H: 4 mm + 0.5 ppm · V: 8 mm + 1 ppm

Kinematic accuracy

H: 7 mm + 1 ppm · V: 14 mm + 1 ppm

Connectivity

Wi-Fi 802.11 b/g/n · Bluetooth 4.0 · USB, UART, event

LoRa radio

Optional · 868/915 MHz · up to 8 km

Corrections and outputs

NTRIP, VRS, RTCM3 · NMEA, LLH/XYZ

Logging

RINEX with events up to 10 Hz · 16 GB

Indicative values. Specifications provided by Emlid. Public prices excluding VAT as published by Emlid (October 2026), shipping not included, subject to change; project and volume pricing on request.

Emlid logo, official distributor

DART Solutions, your official Emlid reseller since November 2026

Buying from DART means support from choosing the equipment right through to the field, from a team based in France.

Advice and selection

We start from your sites and deliverables to choose the right receiver, the right correction source and the right accessories.

Commissioning

Base and rover set-up, NTRIP or radio corrections, coordinate system and ready-to-use Emlid Flow projects.

Training

Hands-on training in the field: surveying, stakeout, accuracy checks and data exchange with the office.

Support and after-sales

A single point of contact for your questions, your updates and liaison with Emlid for warranty claims.

Reach M2 FAQ

Is the antenna included?

Not with the module only (€649 excl. VAT), which accepts your own antenna. The version with a multi-band GNSS antenna costs €897 excl. VAT.

RTK or PPK: which one?

PPK is the most robust for mapping: no radio link during the flight, and processing is done afterwards in Emlid Studio. RTK is useful when the position must be known in flight, for example for an autopilot.

Which cameras are compatible?

Any camera with a hot shoe, using the Reach M2/M+ hot shoe adapter that wires the synchronisation pulse.

Do I need a ground base?

You need reference data: a Reach RS base, a CORS network or an NTRIP source. The unmanned systems kit includes a Reach RS3 base.

Can it be integrated on a robot?

The M2 provides an RTK position to an autonomous system over UART or USB. DART assesses integration on your robotic platforms case by case.

Does DART support drone integration?

Yes: choice of antenna and mounting, camera synchronisation set-up and getting started with the PPK workflow in Emlid Studio.

Equipping your drone with a Reach M2?

Integration, PPK workflow or ground base: we help you make your georeferencing reliable.

Request a quote